Pedir en el Servicio de Dimensionado la madera prensada de 15 mm en las siguientes medidas: 1 trozo de 180x90 cm para el frente, 6 costillas de 30x90 cm, para estructurar el mueble 1 corte de 177x10 cm, 4 de 20x10 y 2 de 26x10 cm, además se necesitan 3 de 49 cm como base interior, 3 como repisas que miden 48,5 y 1 35x180 cm como cubierta del mueble.
Es la pieza de Pladur que se coloca entre la balda inferior y el suelo. Antes de instalarlo, es conveniente colocar unos calzos en el hueco existente entre el suelo y la balda inferior, con el fin de reforzar su consistencia. Tomar las medidas desde el suelo hasta el borde superior de la balda y trasladarlas a una placa de cartón yeso de 1 cm de grosor. Cortar con un cutter.

Instead of permanently mounting my 6-in. vise to a work-bench, I attached it to scrap plywood so I can clamp it wherever I need it. Stack two pieces of 3/4-in. plywood and screw them together with 1-1/4 in. drywall screws. Mark the vise-mounting holes on the plywood and drill 3/4-in. guide holes through both pieces. Recess the nut by drilling through the bottom sheet with a 1-in. spade bit using the 3/4-in. hole as a guide. Fasten the vise to the plywood with bolts sized to match the vise-mounting holes. If the bolt shafts are too long, cut them off with a hacksaw. — LuAnn Aiu. Plus: Learn how to use vise grips to pull nails.


Si no encuentras el sofá de tus sueños, ¡deja de buscar! Hoy te enseñamos a hacer uno con tablas de madera que, además, te servirá de cama. ¿Comenzamos? Para hacerlo necesitarás los siguientes materiales y herramientas: - Tablas de madera. - Sierra de calar. - Lija de mano o lijadora eléctrica. - Taladro con punta de destornillador. - tornillos largos especiales para madera. - Cola de carpintero. ...
How do you divide 11-3/8-in. (or any other mathematically difficult number) into equal parts without dividing fractions? Simple. Angle your tape across the workpiece until it reads an easily-divisible dimension and make your marks with the tape angled. For example, say you want to divide an 11-3/8-in. board into three equal parts. Angle the tape until it reads 12-in., and then make marks at “4” and “8”. Plus: More measuring tips and tricks.
My planer blasts shavings all over the shop floor. I decided to make my own dust chute from 4-in. PVC sewer pipe (which has thinner walls than regular Schedule 40 pipe) and a couple caps. I cut a slit in the pipe and used a heat gun to soften the plastic. That allowed me to open the slit. (Heating PVC releases fumes; ventilation is critical.) I then drilled holes in the flap and screwed it to the planer housing. Finally, I cut a 2-1/2- in. hole in one of the end caps to accept my shop vacuum hose. Works great! — Luis Arce. Here’s what else you can do with PVC pipe.
En está ocasión, y aprovechando restos de madera de palets, vamos a hacernos una sencilla pero práctica y moderna base con ruedas para macetas. Y digo moderna, porque no tiene el típico diseño de listones de madera con las mismas dimensiones (en cuanto al grosor de las mismas). Para dar un toque distinto a la base, he decidido usar listones reciclados de restos de madera de palets, con diferentes ...
Popular and easy to work with, cherry is in high demand for its reddish-brown color and ease of staining and finishing. Cherry likely won’t be at the local home center, but should be at a lumberyard for a somewhat expensive price.[12] This hardwood is a very common material for furniture, and is resistant to normal wear-and-tear, but it is best for indoor pieces.[13]
Ubicar el cuadrado en el banco de corte afirmado con prensas, justo en la segunda línea poner una guía de corte (trozo de madera que sobró de la plancha) que también va sujeto con las prensas. Hacer el corte con la fresadora, calzándola justo en la segunda línea, como la fresa mide 13 mm de ancho, rebajará a cada lado de la diagonal 6,5 mm, para dejar 2 triángulos exactamente iguales.
Finally, as I shared in my post last week on how I learned woodworking, I learned how to use power tools by watching YouTube videos and then just trying them out for myself. I highly recommend this method to learn how to use your power tools. There are lots of videos on specific models of tools too. So, watch a few how-to videos and very importantly, review the tool manual and safety guide for your own tools. Then, go ahead and try the tool out yourself and start using it!

Set the table saw fence so the blade is centered on the seam, then push the whole thing through the saw. If the board edges are quite bowed or curvy, you may need a second pass. If so, unscrew the cleats, reclamp the boards across the middle center, then screw on the cleats again. The screws ding up the ends of the boards a little, so cut the boards you’re jointing a bit long, then trim 1/2 in. from each end to remove the screw holes.


Al pensar en los artefactos, los módulos generalmente son de 60cm y 90cm en el caso de hornos, microondas, encimeras y campanas. Un horno, por ejemplo, mide un poco menos de 60 cm y está pensado para caber perfectamente en un nicho de 60 cm, considerando los costados. En el caso de lavaplatos, estos dependerán de la perforación que se debe realizar en la cubierta y si son instalados sobre la cubierta o bajo esta. En el mercado existen modelos que varían desde 30cm hasta 90cm de ancho. Es importante que el nicho calce dentro del módulo y se le den unos cm de holgura. La sección del escurridor del agua, al estar sobre la cubierta, no afecta en si está apoyado sobre uno o más módulos.
Finalmente la conclusión que he obtenido de todo esto es que lo que aparentemente era una pérdida de tiempo y dinero se ha materializado en mi modo vida. Sé que con esta filosofía de vida no voy a enriquecerme aunque realmente tampoco me interesa. Posiblemente trabajando para otras empresas y ofreciéndoles mis conocimientos podría ganar más dinero y sobre todo evitarme las complicaciones incluidas de trabajar para uno mismo, pero creo que he conseguido hacer todo lo que puedes ver en mi web precisamente por haber escogido otro camino y prefiero seguir asi. Aunque pueda sonar extraño, he aprendido todo lo que sé gracias a la filosofía del "hazlo tu mismo" y del "no necesitas demasiado para trabajar con calidad".
When it comes to woodworking for beginners, I think it’s important to just learn how to use a few of the most essential woodworking tools for beginners. There are so many awesome tools available on the market today, it can be quite overwhelming as well as expensive to try to buy them all and know how to use them. Once you learn the basics of the most essential tools you will be able to start building in no time and feel comfortable learning any other new tools in the future.

Del mismo modo y seguramente por imitación desde muy niño empecé a realizar mis propios proyectos. Al principio eran simples juguetes de madera o inocentes artefactos de guerra infantil. Como me gustaba el oficio de trabajar la madera, a los 13 años inicié los estudios de carpintería en un colegio. Eran muy pocas horas de taller y mucha teoría sin aplicación práctica. Sigo pensando que muchos de esos datos no eran necesarios para aprender el oficio, y los que sí lo eran, solo aprendí a memorizarlos y no a utilizarlos en casos prácticos. Creo que esto es algo fundamental para conseguir abrir tu mente, ver cualquier oficio desde una perspectiva diferente y llegar a solucionar problemas por ti mismo. Por eso y porque estaba en plena adolescencia terminé por desanimarme y después de cuatro años dejé los estudios. Junto con unos pequeños cursos de diseño asistido por ordenador esta fue mi única incursión en la enseñanza.
A board is considered “quarter-sawn” when the growth rings run, more or less, perpendicular to the face of the board. Quarter-sawn boards generally have straight grain and are less prone to shrinkage, compared to other boards. These factors don’t come into play with the 2x4s you use to frame a closet—but it does with the shelves and cabinetry you put into that closet; you want those boards to remain straight, flat and stable.
Con 1 plancha salen 34 triángulos, que pueden alcanzar como sugerencia para hacer un estante mediano y una mesa de centro. -Pedir en el Servicio de Dimensionado que corten la plancha de terciado en 17 cuadrado de 40 cm. Lo que sobre hay que traerlo a la casa porque servirá como guías de apoyo y corte. De estos 17 cuadrado se obtienen 34 triángulos rectángulos
Simply soak a washcloth in water and ring it out a bit so it’s not sopping wet. Put the damp washcloth on the affected area. The water will wick through the wood, and that’s fine. Now, with your iron on its highest setting, place it on the damp washcloth over the affected area, and make small movements back and forth and in circles. Press down firmly and continue until your wash cloth is dry. It won’t take long to evaporate. At this point, the wood fibers are absorbing the water and should expand back to where they were originally. Continue this process and repeat by adding more water until the dents rise up to be flush with the rest of the material.

YP - The Real Yellow PagesSM - helps you find the right local businesses to meet your specific needs. Search results are sorted by a combination of factors to give you a set of choices in response to your search criteria. These factors are similar to those you might use to determine which business to select from a local Yellow Pages directory, including proximity to where you are searching, expertise in the specific services or products you need, and comprehensive business information to help evaluate a business's suitability for you. “Preferred” listings, or those with featured website buttons, indicate YP advertisers who directly provide information about their businesses to help consumers make more informed buying decisions. YP advertisers receive higher placement in the default ordering of search results and may appear in sponsored listings on the top, side, or bottom of the search results page.
The rubber cushion on my old palm sander was wearing thin around the edges. Because of its age, I couldn’t find a replacement pad. As I was drinking my beverage with a foam can cover around it, I realized I could cut the foam to fit the sander and glue it on. I peeled off the old pad, cleaned the metal base and attached the foam with contact cement. Works for clamp-on as well as stick-on sanding squares! You can find can covers at discount and convenience stores. — Allen J. Muldoon
With the right tools and materials, what you build is only limited by your imagination and creativity. So why not have a little fun with the kids and teach them something at the same time? Our woodworker tools and woodworking supplies will help you put together an easy birdhouse, squirrel feeder or butterfly house. The kids will love to use our paint samples to add their creative touch, and will enjoy displaying the finished product in the backyard.

Instead of permanently mounting my 6-in. vise to a work-bench, I attached it to scrap plywood so I can clamp it wherever I need it. Stack two pieces of 3/4-in. plywood and screw them together with 1-1/4 in. drywall screws. Mark the vise-mounting holes on the plywood and drill 3/4-in. guide holes through both pieces. Recess the nut by drilling through the bottom sheet with a 1-in. spade bit using the 3/4-in. hole as a guide. Fasten the vise to the plywood with bolts sized to match the vise-mounting holes. If the bolt shafts are too long, cut them off with a hacksaw. — LuAnn Aiu. Plus: Learn how to use vise grips to pull nails.


With the advances in modern technology and the demands of industry, woodwork as a field has changed. The development of Computer Numeric Controlled (CNC) Machines, for example, has made us able to mass-produce and reproduce products faster, with less waste, and often more complex in design than ever before. CNC Routers can carve complicated and highly detailed shapes into flat stock, to create signs or art. Rechargeable power tools speed up creation of many projects and require much less body strength than in the past, for example when boring multiple holes. Skilled fine woodworking, however, remains a craft pursued by many. There remains demand for hand crafted work such as furniture and arts, however with rate and cost of production, the cost for consumers is much higher.

How do you divide 11-3/8-in. (or any other mathematically difficult number) into equal parts without dividing fractions? Simple. Angle your tape across the workpiece until it reads an easily-divisible dimension and make your marks with the tape angled. For example, say you want to divide an 11-3/8-in. board into three equal parts. Angle the tape until it reads 12-in., and then make marks at “4” and “8”. Plus: More measuring tips and tricks.
When cutting full sheets with my circular saw, I use plastic shelving units as sawhorses. The height is just right and by using three of them, I can make cuts in any direction and the plywood is fully supported. And because the shelving units are made of plastic, I can cut right into them without worrying that they’ll damage my saw blade. Plastic shelves are available for $20 at home centers. — John Tinger. Check out these tips for making long cuts with a circular saw.
There are many factors to consider when deciding what type of wood to use for a project. One of the most important is the workability of the wood: the way in which it responds when worked by hand or tools, the quality of the grain, and how it responds to adhesives and finishes.[9] When the workability of wood is high, it offers a lower resistance when cutting and has a diminished blunting effect on tools.[9] Highly workable wood is easier to manipulate into desired forms. If the wood grain is straight and even, it will be much easier to create strong and durable glued joints. Additionally, it will help protect the wood from splitting when nailed or screwed.[9] Coarse grains require a lengthy process of filing and rubbing down the grain to produce a smooth result.[9]
Cutting sandpaper is a quick way to dull your scissors or utility knife blade. Instead, I fastened a hacksaw blade to the edge of my workbench. I slipped a washer behind the blade at each of the mounting holes so a sheet of sandpaper to easily slides in behind the blade. I fold the paper where I want to cut, just as a reference. — Kim Boley. Try some of these storage solutions!

Whether you are a beginner or a DIY professional, if you have a love for the craft of woodworking The Home Depot has got you covered. We have all the essential tools for woodworking that let you hone your craft. Our huge selection of drill presses and miter saws will put the power in your hands to complete your projects faster and easier. And whether you are looking for the strength of a powerful router or the versatility of a lathe, you can find everything you need to help with projects, large and small. If your carpentry plans also include building materials, you don't need to look any further than The Home Depot. From wood and lumber to decking and fencing materials, it's all right here.
Como puedes ver en mis vídeos, no son necesarias demasiadas ni costosas herramientas eléctricas para realizar tus propios proyectos. Lo indispensable en tu taller será una caladora, una sierra circular y una fresadora. Cualquiera de las tres herramientas servirán para acoplar a tu primera sierra de mesa. Lo ideal es desarrollar un rápido y sencillo sistema de anclaje y desanclaje a la sierra de mesa para de ese modo poder seguir utilizándolas como portátiles en pocos segundos. Además de esto, deberíamos contar con un atornillador a batería, una lijadora y un aspirador.
With the right tools and materials, what you build is only limited by your imagination and creativity. So why not have a little fun with the kids and teach them something at the same time? Our woodworker tools and woodworking supplies will help you put together an easy birdhouse, squirrel feeder or butterfly house. The kids will love to use our paint samples to add their creative touch, and will enjoy displaying the finished product in the backyard.
Los nichos y espacios muertos bajo la escalera pueden tener una cara completamente distinta con un mueble que se diseñe adaptándose a cada centímetro del área en cuestión. La propuesta de la arquitecto Andrea Stortoni fusiona la escalera con el mueble de madera maciza bajo la escalera utilizado para albergar el televisor, una idea práctica y genial para hacer en casa.
×