Después habrá que crear el soporte, que puede ser para colgarlo o para mantenerlo en pie. Para ello, debes doblar el alambre que teníamos en los materiales en la forma que ves en la imagen superior para poder colocarlo sobre una superficie lisa. En el caso de que prefieras colgarlo, te bastará con que hagas un agujero en la parte superior para luego colocarlo en un cuelgafácil en la pared. ¿A qué ha sido fácil el proceso de personalizar este marco de fotos? ¿Te animas a ponerlo en práctica?
When it comes to woodworking for beginners, there are 6 things that I think are essential to know for how to start woodworking. I’m going to discuss each of these tips in hopefully a really simple way to make it a breeze to understand, so you can get to the fun part of actually starting to woodwork! I wish when I started and was learning how to woodwork that I had a simple beginner tips guide like this one!
Es la pieza de Pladur que se coloca entre la balda inferior y el suelo. Antes de instalarlo, es conveniente colocar unos calzos en el hueco existente entre el suelo y la balda inferior, con el fin de reforzar su consistencia. Tomar las medidas desde el suelo hasta el borde superior de la balda y trasladarlas a una placa de cartón yeso de 1 cm de grosor. Cortar con un cutter.

A clean well-organized environment is key to staying A clean well-organized environment is key to staying happy. The same goes for your desk. Keep the clutter at bay and organize all of your small essentials with the Dickies Work Gear 57050 Mug Organizer. Designed to fit over most mugs this clever caddy features 8 outer pockets and 6 ...  More + Product Details Close


Old doors laid across sawhorses make great temporary workbenches, but they take up a lot of space when you’re not using them. Instead of full-size doors, I use bifold doors with hinges so I can fold them up when I’m done working. They’re also easier to haul around in the pickup for on-the-road jobs. — Harry Steele. Here are 12 more simple workbenches you can build.
Lacking a jointer? Use reader Court Kites’ awesome tip to create perfectly matched glue joints on wavy or bowed board edges. Lay the boards on a flat surface, then clamp them across the middle with a bar clamp. Lay two 8-in. long by 1-3/4 in. wide scrap boards across each end and screw them in with four 1-1/4 in. long screws, two per board. Keep the screws well away from your future cutting line!
Estimados, si bien el muy lindo el mueble, hubo un un error garrafal con respecto al radiador, esta bien la separación en la parte superior del mueble para la salida de aire caliente, pero para que esto suceda se debe saber que estos equipos funcionan por circulación de aire ( aire frío de la habitación pasa por abajo y sale caliente por arriba) un corte en la parte de abajo falto
Instead of permanently mounting my 6-in. vise to a work-bench, I attached it to scrap plywood so I can clamp it wherever I need it. Stack two pieces of 3/4-in. plywood and screw them together with 1-1/4 in. drywall screws. Mark the vise-mounting holes on the plywood and drill 3/4-in. guide holes through both pieces. Recess the nut by drilling through the bottom sheet with a 1-in. spade bit using the 3/4-in. hole as a guide. Fasten the vise to the plywood with bolts sized to match the vise-mounting holes. If the bolt shafts are too long, cut them off with a hacksaw. — LuAnn Aiu. Plus: Learn how to use vise grips to pull nails.
Clamping up four mitered corners is tricky. You can buy specialty clamps for this, but I make my own. Here’s how to do it. Start with a long 1×4, as it’s easier (and safer) to clamp for making the angled cuts than a short piece. Mark out the blocks, and then drill a 1-in. diameter hole in the center of each one. The hole prevents the blocks from getting glued to your project. Cut 45-degree angles tangent to the hole, and then cut the blocks free from the long board. We’ll walk you through how to make one for your home shop.
There are a few things particleboard is NOT. It’s not medium density fiberboard (MDF)—a material with greater density and weight composed of more uniform particles. It’s NOT oriented strand board (OSB), a material composed of large wood chips and strands that’s structurally equivalent to plywood. It does NOT have great nail or screw holding ability, nor is it all that water resistant; water can quickly cause the material to swell and lose structural integrity. But if you need something flat and cheap for use in a dry place, particleboard will do you proud. Learn how to make a plastic laminate tabletop with a particleboard substrate.
Disfrutar de la carpintería y del bricolaje y, además, tener las herramientas necesarias y de espacio para trabajar es un 'lujo'. No solo porque podemos dar rienda suelta a nuestra creatividad a la vez que disfrutamos de nuestra pasión, sino porque no habrá nada en el hogar que se nos resista. ¿Qué tenemos un problema o necesitamos resolver algo? ¡Acudamos al bricolaje!
×